低平板挂车

SCHWARZMÜLLER Tieflader mit gekröpftem Plateau

Excerpt from the equipment list. Complete equipment list available upon request.

Frame
* Steel welded construction with front frame extension
* Front corners beveled, rear bevel
* Access ramp with excavator bucket recess in the center = recess at the rear between the longitudinal beams, approx. 2,300 mm long

Integrated into the outer frame
* 4 pairs of approx. 4 t lashing bars
* 7 pairs of recessed, retractable approx. 10 t lashing rings (2x on the raised platform
* 1x in the front extension slope
* 3x in the low-bed between the wheel recesses and 1x in the access ramp
* 2 pairs of wheel recesses
* 1 pair of wheel recesses, approx. 2,300/1,270 x 400 mm (L1/L2 x W)
* Front, after the extension, incl. one-piece drivable aluminum cover, for max. surface load of approx. 11,650 daN/piece
* 1 pair of wheel recesses, approx. 1,390/590 x 270 mm (L1/L2 x W), between the 3rd and 4th axles, incl. one-piece drivable aluminum cover
* Suitable for the transport of wheel loaders with a wheelbase of approx. 2,700 - 3,600 mm, with wheel diameter of approx. 1,485 - 1,740 mm
* Wheel loader overhang at the rear max. 2,220 mm, width between the wheel recesses approx. 1,255 mm (= outer/outer longitudinal beam)
* Reinforced ball-bearing swivel ring for a total weight of 44 t

Frame attachments
* 5 pairs of receiving pockets in the outer frame for square tube supports, approx. 100 x 50 x 5 mm (3x in the low-bed and 2x on the raised platform)
* 4 pairs of foldable approx. 10 t lashing rings
* Arrangement: 1 pair at the front on the raised platform, inside the longitudinal beams
* 1 pair at the very rear in the excavator bucket recess on the left and right
* 1 pair at the front on the raised platform in front of the extension, inside the longitudinal beams
* 1 pair in the low-bed at the rear in front of the access ramp
* Towing device in the excavator bucket recess on the left and right: Fixed drawbar with approx. 50 mm heavy-duty towing eye
* Extended design, silent block bearing
* Drawbar retaining spring with tensioner, truck coupling height from approx. 775 mm to approx. 975 mm, drawbar length approx. 1,800 mm

Support system
* 2 hydraulic supports at the rear - individually operated
Rjdpfjzdmiksx Aifjw
* Control unit housed in a separate stainless steel box

Axles
* SAF air suspension low loader axles with drum brakes
* Load capacity approx. 11 t/axle, S-cam brake approx. 300/200 mm
* Automatic brake linkage adjuster

Wheels
* 16 tires 245/70 R 17.5, 146/146F
* Manufacturer Conti HTR2, 16 steel rims 6.75 x 17.5, with offset, painted black
* Black plastic wheel nut covers

Braking system/suspension
* Two-line compressed air braking system according to ECE Directive R13
* Manufacturer Wabco EBS system 4S3M, 1st + 3rd axle sensed, RSS/RSP
* Stability program, spring brake parking brake on 3rd + 4th axle
* Aluminum air tanks, brake/air connection lines with 2 single coupling heads, yellow/red, EBS/ABS connection cable, rubber strap as holder for EBS and electrical plug, air suspension with lifting and lowering device, operable separately at the front and rear
* Automatic adjustment to programmed driving level from 15 km/h

Floor
* Softwood floor approx. 50 mm, impregnated, approx. 5 - 10 mm
* Protruding above the top edge of the frame, steel tear plate cover over the rear wheels

Ramps
* 2 pieces foldable 2-part steel access ramps
* Hydraulically foldable, slope approx. 10 degrees
* Length approx. 2,750 + 1,350 mm, width approx. 800 mm, with hardwood floor approx. 50 mm, impregn

该广告为自动翻译，可能存在翻译错误。