三辊卷板机Kramer
RHM III 120/1000
三辊卷板机
Kramer
RHM III 120/1000
製造年份
1990
狀況
二手
位置
Weiterstadt 

顯示圖片
显示地图
机器数据
价格和位置
- 位置:
- Rudolf Diesel Str. 23a, 64331 Weiterstadt, Deutschland

撥打
优惠详情
- 產品ID:
- A20815387
- 最後更新:
- 於 22.12.2025
描述
Type RHM III 120 v-1000
Roll diameter: 120 mm
Working length: 1000 mm
Sheet thickness: up to 5.0 mm
400 Volt
Kramer Maschinenbau GmbH
Description
The features described for the RH II series also apply to the RHM III series. These round bending machines are designed for continuous operation under maximum load. The lower shaft is adjustable via a worm gear.
For models RHM III 90 – RHM III 130, the geared brake motor is flange-mounted on the outside, while models RHM III 140 to RHM III 180 are equipped with an internally flange-mounted geared brake motor.
All motorized machines come standard with electrical safety control. Operation for forward and reverse is carried out using a double footswitch.
Additional features on type RHM III:
▪ Powerful thermally protected geared brake motor
▪ Electrical safety control
▪ Convenient double footswitch for forward/reverse
▪ Three-shaft drive (particularly recommended for thin sheet work)
▪ Drive system with two operating speeds
Lodpox Niu Nofx Abfsak
▪ Overload protection via slipping clutch
▪ Motorized rear shaft adjustment
▪ Motorized lower shaft adjustment
Standard equipment:
▪ Gear side drive
▪ Three-shaft construction
▪ Asymmetrical shaft arrangement
▪ Upper shaft can be swung out to the front
▪ Adjustment of lower and rear shafts via handwheel
▪ Conical bending by tilting the lower and rear shafts
▪ Initial bending capacity equals round bending capacity
Optional equipment:
▪ Device for conical rolling
▪ Upper shaft with grooved edge
▪ Lower and rear shafts with wire groove
▪ Surface-hardened shafts
▪ Ground shafts
廣告是自動翻譯的,翻譯中可能會出現一些錯誤。
Roll diameter: 120 mm
Working length: 1000 mm
Sheet thickness: up to 5.0 mm
400 Volt
Kramer Maschinenbau GmbH
Description
The features described for the RH II series also apply to the RHM III series. These round bending machines are designed for continuous operation under maximum load. The lower shaft is adjustable via a worm gear.
For models RHM III 90 – RHM III 130, the geared brake motor is flange-mounted on the outside, while models RHM III 140 to RHM III 180 are equipped with an internally flange-mounted geared brake motor.
All motorized machines come standard with electrical safety control. Operation for forward and reverse is carried out using a double footswitch.
Additional features on type RHM III:
▪ Powerful thermally protected geared brake motor
▪ Electrical safety control
▪ Convenient double footswitch for forward/reverse
▪ Three-shaft drive (particularly recommended for thin sheet work)
▪ Drive system with two operating speeds
Lodpox Niu Nofx Abfsak
▪ Overload protection via slipping clutch
▪ Motorized rear shaft adjustment
▪ Motorized lower shaft adjustment
Standard equipment:
▪ Gear side drive
▪ Three-shaft construction
▪ Asymmetrical shaft arrangement
▪ Upper shaft can be swung out to the front
▪ Adjustment of lower and rear shafts via handwheel
▪ Conical bending by tilting the lower and rear shafts
▪ Initial bending capacity equals round bending capacity
Optional equipment:
▪ Device for conical rolling
▪ Upper shaft with grooved edge
▪ Lower and rear shafts with wire groove
▪ Surface-hardened shafts
▪ Ground shafts
廣告是自動翻譯的,翻譯中可能會出現一些錯誤。
您的广告已成功删除
发生错误







