低装载机

Fliegl ZTS 200 P

Further information
Chassis low loader trailer
Welded steel construction
Turntable with strong ball bearing slewing ring, storage box embedded in turntable front end
Folding rear support
Wheel chocks with holder
Aluminum side collision protection
Half-shell mudguards on 1st axle, quarter-shell mudguards in front of and behind the 2nd axle
with anti-spray flaps behind each axle
1 plastic tool box, with shelf, w=620/h=360/t=440 mm, lockable with a padlock. (lock not included in scope of delivery)
Widenings extendable to 3,000 mm (not in rear slope)
(However, the track width of the construction machinery or vehicles to be transported must not exceed the outer frame width of 2,550 mm), storage compartment for wooden planks in the middle of the loading area, wooden planks 70 mm for widening to 3,000 mm,
Low loader lashing eyes
3 pairs of lashing points each 10 tons integrated in the floor at the front
6 pairs of lashing points at the top and sides, each 10 tons, integrated in the outer frame
1 x according to the rest of the neck area distributed between them, spacing not greater than 1200 mm,
1 x rear slope
5 pairs of ring lashing eyes embedded in the outer frame, 5 tons each (instead of stake pockets)
Trailer drawbar Turntable
Drawbar with tested 40 mm drawbar eye
Axles + suspension
SAF drum brake axles
Axle/chassis laser-measured Reduction in tire wear and fuel consumption
Parabolic suspension with maintenance-free steel-rubber bearings
Wheels and tires
235 / 75 R 17,5
at the manufacturer's choice
Twin steel rims, factory silver
Brake system
2-line compressed air brake system
Spring-applied parking brake
2 non-interchangeable coupling heads at the front, with connecting cables to the motor vehicle,
ABS and ALB, with ABS plug at the front, with connecting cable
Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS!
Electrical system
24 volt, multi-chamber lights, amber LED lighting at the side
2 white/red rear lane departure lights
2 white position lights at the front
1 rotating beacon with holder, switched via parking light (removable light)
2 pairs of warning signs, double LED illuminated and extendable to 3,000 mm
2 x 7-pin interchangeable plugs at the front, with connecting cable,
floor
Front area steel floor,
then with 70 mm softwood floor, steel/ checker plate flooring in the wheel arch area
Rear slope with 70 mm softwood floor
Low loading area incl. rear slope 8 200 mm
Drive-on ramps
Steel ramps 2,800 mm long, 750 mm wide, can be moved sideways
Additional ramp safety device hinged at the bottom (to prevent the ramps from slipping sideways, not in conjunction with hydraulic side ramp displacement)
Casdji Ri N Hjpfx Aftea
covered with wood
with spring lift support
Operating instructions
A special permit is required for axle loads of 10,000 kg. The permit must be applied for individually in each federal state; the legislator does not have to give a commitment for 20 tons GG. Customer risk.
The specified total weight is technically possible; depending on the load, the total weight may not be reached if the permissible axle/support and fifth-wheel loads are observed.
Approval / plates
Country of approval: Germany
Test approval according to EG 2007/46
24/7 service hotline
Prepared for two-line license plate holder
Contour markings with reflective strips to ECE R 048, white at the sides and red at the rear
Warning sign according to ECE - 70
Paint finish
Frame DB nova gray
Drive-on ramps hot-dip galvanized

Attentio

廣告是自動翻譯的，翻譯中可能會出現一些錯誤。