低平板挂车

Fliegl VTS 400 Sonder

The images shown are archive photos!

Permissible / technical gross weight: 24,000 / 40,000 kg
Permissible / technical payload approx.: 14,600 / 30,600 kg
Permissible / technical axle load: 24,000 / 40,000 kg
Unladen weight (basic version) approx.: 9,400 kg +/- manufacturing tolerance

Overall length approx.: 12,120 mm
Overall width max.: 2,750 mm
Neck length approx.: 2,850 mm
Low bed platform length in wheel track area incl. rear bevel approx.: 7,145 mm
Rear bevel length approx.: 850 mm
Frame width approx.: 2,750 mm
Loaded bed height in low bed approx.: 900 mm
Drawbar height approx.: 950 mm
Drawbar length approx.: 1,700 mm

Chassis: Low-bed trailer
Steel welded construction
Turntable with heavy-duty ball bearing slewing ring
Foldable rear support
2 wheel chocks with holders
Aluminum side underrun protection
1 plastic toolbox,
Extendable width up to 3,250 mm (not at rear bevel) (track width of machine/vehicles to be transported must not exceed outer frame width of 2,750 mm)
Storage compartment for wooden boards in the center of the loading area
70 mm wooden boards for extension to 3,000 mm
2 pairs of stake pockets in the low bed recessed into the longitudinal beams
Lashing points low-bed:
2 pairs of lashing eyes on neck, 5 tons each
1 pair of lashing eyes in rear bevel
4 lashing eyes recessed in the middle of the floor
2 pairs of keyhole profiles in wheel track area for insertion of longitudinal guide rails and as additional lashing option
6 pairs of lashing pins recessed in outer low-bed frame, 10 tons each
5 pairs of stake pockets recessed in the outer frame of the low bed
4 additional pairs of 10 ton lashing eyes:
- 1x on neck
- 3x recessed in low bed floor

Trailer towing device, turntable design
Drawbar with certified 50 mm towing eye

Axles & Suspension
Drum brake axles
Parabolic suspension with maintenance-free steel-rubber mounts and mechanical axle load equalization front and rear (rocker balancing)

Wheels and Tires
235/75 R 17.5"
Steel twin wheels, factory silver finish

Njdpfx Abjyxq A Hjdswd
Brake System
2-line compressed air brake system
Spring-loaded parking brake
2 foolproof couplings at front, with interconnecting lines to tractor
ABS and ALB, with ABS socket at front and connection cable
Note: The trailer may only be towed by vehicles ensuring proper ABS functionality!

Floor
Neck area with steel / checker plate covering
Followed by 70 mm softwood floor; in wheel arch area steel / checker plate
Rear bevel with 70 mm softwood floor

Loading ramps
Steel ramps, 2,800 mm long, 750 mm wide, laterally adjustable, with wooden covering
Hydraulically operated via tractor auxiliary drive

Operating Notes
At 10,000 kg axle load, an exemption permit is required, only indivisible loads permitted!
Note! Oversize length and width require a permanent special permit.
When applying for an exemption for regulated heavy haulage, an axle load indicator is required for air-suspended vehicles! This applies to any deviation from § 34 StVZO (axle and permissible total weight overrun), which requires an exemption under § 70 StVZO.
The specified gross weight is technically possible; depending on the load, the total weight permitted by axle, support, and kingpin loads may not be achieved. (Poor driving or tracking behavior may occur due to improper load distribution)

The images shown are archive photos!

该广告为自动翻译，可能存在翻译错误。